how to clean mass air flow sensor chevy equinox

A mass airflow sensor MAS determines the mass of air entering a vehicles fuel injection engine and passes that data to the Engine Control Unit or ECU. Unplug the electrical connector from the mass airflow sensor.

Never Do This When Cleaning Your Mass Air Flow Sensor Youtube

The two most common trouble codes in relation to the MAF sensor are.

. This automotive maintenance tutorial was specifically written to assist owners of the third generation 2018 2019 and probably also the face-lifted or revised 2020 2021 and 2022 model years GM Chevrolet Equinox SUV in cleaning or changing the MAF mass air flow sensor for the Ecotec 15 liter turbocharged four. The air mass information is necessary to calculate and deliver the correct fuel mass needed by the engine. The air mass information is necessary for the ECU to correctly balance and deliver the correct amount of fuel to the engine.

With the Chevy Equinox P0101 means the the Mass Air Flow MAF sensor has a RangePerformance problem. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone. Make sure you only pull on the connector and not the wires.

Step 2 Remove the MAF sensor. Once off your MAF sensor should look like the one in the photo. You should only need to give it 1015 quick blasts around the interior of the sensorIn addition to this clean the sides of the component as well as its housing connections and terminalsIf you are using a hot wire mass air flow sensor you must ensure that the cleaner does not come into.

Mass Air Flow MAF Sensor Circuit Malfunction. Use a flat head screwdriver to loosen the hose clamp screws. A bad mass airflow sensor can leave your Chevy Equinoxs engine running rough or even inoperable.

Place the sensor on a towel for cleaning. Reliable and quiet your Chevrolet Equinox small crossover SUV is perfect for highway driving and it gets respectable gas mileage as well. Install the new MAF on your Chevrolet.

Mass Air Flow MAF Sensor Circuit RangePerformance Problem. They are the vane meter and the hot wire. When a vehicles mass airflow sensor is faulty or defective it can cause a variety of problems and usually.

If your hands slip off the connector it is good to wear gloves with a. It should be considered a high priority to fix as the MAF sensor not reading properly can really make an impact on the performance of the vehicle. Chevy Express P0101 Diagnosis.

Remove the screws that hold the mass airflow sensor in place. The most common signs of bad mass air flow sensor MAF in Chevy HHR are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe. A mass airflow sensor is used to determine the mass of air entering the engine.

Plug the electrical connector until it locks in place. Two Screws On Side. The Intake Air Temperature IAT sensor is also built into.

Tighten the screws so that they are snug. The most common signs of bad mass air flow sensor MAF in Chevy Equinox are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe. MAF Sensor Circuit Low.

While pulling the connector squeeze the tab on either side of the harness. Here are a couple of others. The mass air flow sensor is part of the engines intake system and is located.

This is great because it helps you narrow down the problem. Pull the air inlet hose off the sensor and then pull the sensor off of the air filter housing. Remove the mass air flow sensor from the car or truck.

Here are the basic steps involved in cleaning a mass air flow sensor. The check engine light will require a few days of driving to reset. Disconnect the mass airflow sensor from the electrical connector.

And lets get started with the actual step by step cleaning of the GM mass air flow MAF sensor Buick Chevrolet Oldsmobile Pontiac and GMC models. There are two common types of mass airflow sensors in usage on gasoline engines. Our trucks have a hot wire sensor.

Mass Air Flow Sensor. Remove The MAF Sensor From Vehicle. Also clean the sides of the part its housing its connectors and its terminals.

Mass air flow MAF sensors measure the amount of air entering the engine. If you have a hot wire mass air flow sensor make sure the cleaner doesnt get onto the hot wires or plate. Alright enough of the bs.

When you are finished cleaning the sensor place it on the clothApply the cleanser. Today I show you where your Mass Air Flow MAF Sensor is located and how to remove and clean it. A MAF sensor diagnostic trouble code DTC stored in your vehicle computers memory.

There are two hose clamps on each side of the MAF sensor that hold it in place. We will cover exactly what that means and potential fixes for it below. It passes this information onto your Equinoxs ECU.

The mass airflow sensor commonly abbreviated to MAF is one of the most important engine management sensors. Mass Air Flow MAF Sensor Circuit Low Input. The symptoms of a bad mass air flow sensor include low engine power poor fuel economy an engine that wont start a check engine light on the dash and a gas.

A MAF sensor measures the density of the air entering the intake manifold. 2018 Equinox Air Box. The mass air flow sensor is part of the engines intake system and is.

Apply the cleaner 10-15 blasts around the inside of the sensor will do. There are other codes related to the mass air flow sensor as well but these are the most common ones.

P0100 Mass Air Flow Circuit Malfunction

Chevy Equinox Gmc Terrain Maf Iat Sensor Cleaning Youtube